Mobile Site Office Accommodation, Mobile Site Office, Portable Prefab Office, Mobile Prefab Site Offices

MOBILE SITE OFFICE ACCOMMODATION – CONFIGURED TO SUIT YOUR ON-SITE NEEDS

Why accept dreary, box-like ‘here-today-and-gone-tomorrow’ mobile site office accommodation, when you can occupy our portable prefab Speedoffice units.

These attractive prefab site offices are visible proof that temporary mobile site office accommodation can be aesthetically pleasing and comfortable to work in, as well as practical.

Our mobile prefab site offices can be configured to suit you, from a single office to an entire complex, complete with boardroom.

In fact, you’ll be sorry when you have to move out!

SPEEDOFFICE SPECIFICATIONS

GENERAL CONSTRUCTION

Units that are 6, 9 and 12 m in length:
Full-length, full-width structurally welded steel chassis with two 175 x 50 mm lipped-channel, longitudinal beams. Outriggers and cross-members are of 75 x 38 mm channel.

Units that are 15 and 18 m in length:
Full-length, full-width structurally welded steel chassis with two 250 x 75 mm lipped-channel, longitudinal beams. Outriggers and cross-members are of 75 x 38 mm channel.

The complete assembly is sandblasted and coated with self-etch red oxide primer. For added protection, the chassis is coated with a waterproof, malleable compound called Plaswax or similar which forms a tenacious wax-like surfacing.

SIDEWALL CONSTRUCTION

The standard exterior and interior finish is 0,5 mm Chromadek, which is a galvanised, prepainted (frost-white) finish. The perimeter and internal walls are fully insulated with 40 mm thick high-density foam. As an optional extra, chromadek sheeting with a decorative woodlike finish can be used for internal wall finishes.

PLUMBING

Copper, stainless steel, or Polycop piping is used for water supply, and PVC fittings for sewerage and wastewater.

ROOF & CEILING CONSTRUCTION

The roof is a pitched roof construction consisting of the following:

Roof exterior is galvanised sheeting
Ceiling insulation is 40 mm thick high-density foam sandwiched between 0,5 mm white chromadek sheeting
Ceiling finish is 0,5 mm white chromadek ceiling

WINDOWS

All window frames are aluminium, top-hung and fitted with 4 mm thick glass. The area of the windows is equal to or greater than 10% of the gross floor area of each habitable room.

FLOOR CONSTRUCTION

Treated timber floorboards, 18 mm thick, are glued and screwed to cross-members and covered in 2 mm industrial vinyl welded at joints. Carpet covering optional extra.

ELECTRICS

Units are wired for connecting to 220 volt supply, in accordance with SABS 0142:1987, and are fitted with earth-leakage protection and distribution board. Lights, plugs, geyser and interior electrical fittings are installed as shown on the layout diagrams.

TECHNICAL SPECIFICATIONS


Description	Model	Model	Model	Model	Model	Model
	S6241	6301	S96301	S12301	S15341	S18341
Length (ext)	5 820	5 820	9 300	11 620	15 100	17 420
Length (int)	5 740	5 740	9 220	11 540	15 020	17 340
Width (ext)	2 420	2 990	2 990	2 990	3 580	3 580
Width (int)	2 260	2 910	2 910	2 910	3 500	3 500
Height (int)	2 400	2 400	2 400	2 400	2 400	2 400
Electrics	Standard	Standard	Standard	Standard	Standard	Standard
Aluminium Windows	Standard	Standard	Standard	Standard	Standard	Standard
Vinyl Floor	Standard	Standard	Standard	Standard	Standard	Standard
Wall Insulation	Standard	Standard	Standard	Standard	Standard	Standard
Roof Insulation	Standard	Standard	Standard	Standard	Standard	Standard
All dimensions given in mm)	All dimensions given in mm)	All dimensions given in mm)	All dimensions given in mm)	All dimensions given in mm)	All dimensions given in mm)	All dimensions given in mm)

TRANSPORT & HANDLING

It is extremely important that the following points are taken into consideration before delivery can be effected:

Site should be level and compacted. It should not slope more than 200 mm over the length and 100 mm over the width of the unit.
Site must be accessible for an abnormally large load. All trees and/or other obstacles that may be in the way must be removed beforehand to allow easy access.
Gates into property must be a minimum of 4 m wide, and truck must have a straight run-up of at least 25 m, to allow bigger units (9 m and upwards) to be offloaded into position, and allow trucks to drive out from under unit after having lifted it.
Unit will be dropped onto trestles and levelled in order to allow doors to open freely. Final levelling must be done by client unless siting is done and charged for by Speedspace.
A site inspection prior to delivery can be arranged.
All equipment used for loading and off-loading of units is certified and load tested.

OPTIONAL EXTRAS

Exterior skirting
Carpets
Burglar bars
Flyscreens for both windows and doors

Curtains or blinds
Air conditioner
Three-phase electrics
Kitchen appliances (gas or electric)

Geysers (gas or electric)
Carports
Floor insulation
Other fittings/applications as per customer request